Muchmore Racing









HOME > Support
     
FLETA USB Link V1.8 Pc Program (ENG)
ME-FLP2K FLETA PRO V2 Brushless ESC Black
File DownLoad : FLETA_USB_Link_V1.8.zip   

Caution: Please check below matching chart before SHR program card and ESC firmware update.
If using improper firmware may cause failure.  

FLETA USB Link V1.8 Pc Program (ENG)
 
Download "FLETA_USB_Link_V1.8.zip file.
01.jpg

Unzip the downloaded file.

Click "MuchMore V1.8 Setup" file for setup.

i01.jpg
 
Click 'Next' Button

i02.jpg
 
Click 'Next' Button

i03.jpg
 
Click 'Next' Button

i04.jpg
 
Click 'Next' Button

i05.jpg
 
Click 'Install' Button

i05-1.jpg
 
Installing 'FLETA USB Link V1.8 program in the PC'

i06.jpg
 

When the installation is complete, THE USB Driver setup screen appears.

Click 'Next' Button

i07.jpg
 
Check the 'I accept this agreement' and Click 'Next' button

i08.jpg

Click 'Finish' Button'
 
i09.jpg
 
Installed 'Muchmore Racing FLETA USB Link V1.8 program in the PC'

i10.jpg
 
If you cannot install to PC. Check the compatibility.

[ FLETA USB Link V1.6 How to used ]

Do not forget to disconnect the battery with the connector when the PC connect the program card certainly.
Please pay attention to this point especially, connect +,- has been causing huge damage.


Caution 1.
If you use KO Propo`s Receiver, Remove ESC connector from your KO PROPO`s receiver.
i12.jpg
 
Caution 2.  (If you use FLETA PRO V2 or FLETA M8 ESC)
Before connecting USB cable to your PC, make sure switch position is ON.
02fdda93ec1c0ee3496f7596384457d7_1476883982.97.jpg
 

Caution 3.  (If you use FLETA EURO V2)


Firstly connect the battery with ESC, then connect SHR program card with ESC.
Click ESC at Device section, turn on ESC.
(Caution: Do not disconnect the battery before firmware update is complete. 


Untitled-1.jpg
Click the icon of 'Muchmore Racing FLETA USB Link V1.6' and run this program.

f01.jpg

Once the card is connected to the program, 'USB' Connection is turned on.
 
f02.jpg

The person who first used the firmware, please SHR Program Card firmware update firstly.
    Without the firmware program, it does not operate normally.

- Check -
    Top menu > Device > Program Card
    In case of the connecting, mark 'ON' - 'Program Card Connected'
    If not, Please check your cable connecting firmly. 

f03.jpg

Move the 'FIRMWARE MENU'
Choose the FLETA SHR VX.XX in the Change Firmware. Click the PROGRAM CARD FIRMWARE SAVE' button.
Please wait until finishing the text of ready box in the bottom part (running 1~100% and pop the finished text).
Do not remove the connector during the update the firmware, this may cause the equipment failure.
 
f06.jpg

 Top menu > Device > ESC
In case of the connecting, mark 'ON' - 'ESC Connected'
(If you used to FLETA EURO V2 ESC, turn on ESC)

Move the 'FIRMWARE MENU'
Choose menu what you want Firmware. Click the ESC FIRMWARE SAVE' button.
Please wait until finishing the text of ready box in the bottom part (running 1~100% and pop the finished text).
Do not remove the connector during the update the firmware, this may cause the equipment failure.

After done, TOP Menu > Device > Fix mode.
If do not,  this may cause the equipment failure.
 


Power Level 
Change to single stage . previous version is two stage
Value Level 1 to 30 
You can setup for more widely throttle response feeling

BT(Bottom) Soft Power
Modified drivers often feel the power of the bottom throttle is too aggressive. 
Little throttle input usually brings too much power to the car and make it hard to control at the corners.“Bottom Soft Power ” means the strength of  bottom soft power effect. The higher the “Bottom Soft Power ”  value, the more obvious the softening effect.

BT(Bottom) Soft TH Range 
“Bottom Soft TH Range ” means the specific throttle range within which Bottom Soft Power effect will be generated. For example if you set this item to 20%, then the “Bottom Soft Power ” will be generated within the throttle range between 0% and 20%.

Brake Rate Control 
This item is used to control the brake response. It’s adjustable from 1 to 20 (step: set up value "1" the lower the brake rate, the more limit on the brake response. A suitable rate can help driver to brake his vehicle properly. Generally, you can set it to a high value to have a quick brake response if you are proficient at brake control.

Coast 
It allows the motor to gradually lower RPM when reducing the throttle from full or near full speed back to neutral. The vehicle will not abruptly slow when the throttle is reduced to return to the neutral position. The bigger the value, the more the “COAST” will be felt. For example, COAST of 0 deactivates, and a COAST of 10% would be the maximum amount of COAST.

COAST?
When a vehicle is operated with smaller pinions and larger spur gears the vehicle tends to create a feel of braking known as “gear brake”. COAST is to allow the car to roll (coast) as if the vehicle was geared with a larger pinion. The Coast function brings better and smoother control feelings to racers. Also some drivers will refer to this feel as how the traditional brushed motors felt --- they “COASTED” more because the armature with the wire on it was heavy and harder to stop spinning - in the brushless motor the rotor being relatively light stops spinning more abruptly. 
The “Coast” will be void (even if you set it to any value besides 0) if the above “ drag brake ” is not “0%”.
SUPPORT LIST